What we found
- The tide reaches almost 30 km inland. Each rise pushes up the Parramatta River, past the Opera House, under the Harbour Bridge and past Gladesville.
- The sea itself gets only a few kilometres in. The Harbour Bridge is 8 km from the Heads, and new sea water never reaches it in one tide.
- The water runs fastest where the harbour narrows. Under the Harbour Bridge it ran almost twice as fast as at the Heads.
- Port Phillip Bay takes in about twenty times as much. About half a million Olympic pools pour in through the Rip before sunrise.
The story: how far does one tide reach in Sydney Harbour?
Twice a day the sea outside Sydney rises and falls. In the week we mapped, 24 September to 1 October 2026, it moved by up to a metre and a half.
All of that water comes in and goes out through the Heads, the gap between North Head and South Head. The rise and fall then runs up the Parramatta River almost 30 kilometres from the sea. Then it all drains out again, twice a day.
Where does the water run fastest?
The Heads are wide and deep, so the water there moves calmly. It runs fastest where the harbour narrows. Under the Harbour Bridge it ran almost twice as fast as at the Heads, and nearly as fast at Gladesville Bridge.
At the Spit, all of Middle Harbour fills and drains through one narrow channel.
How much water comes in on each tide?
About 26,000 Olympic pools of sea pour into Sydney Harbour on a rising tide, all of it through a gap about one and a half kilometres wide. On the morning we mapped, the harbour was full by seven. Then the extra water poured back out to sea.
Does the sea water reach the city?
Not in one tide. We followed water from the open sea as a tide came in. Most of it got less than a kilometre past the Heads, and the furthest about three and a half. The harbour water mostly moves up and back.
It flushes out slowly. Over a whole week of tides, with no wind or rain, only about 1 in 20 drops inside Watsons Bay reached the open sea.
The same tide in Port Phillip Bay
Port Phillip Bay in Melbourne has one way in from the sea, the Rip, a gap about three kilometres wide between Point Lonsdale and Point Nepean. On Thursday 26 November 2026, the biggest tide of the month, about half a million Olympic pools of sea pour in before sunrise. The bay rises by about two thirds of a metre.
That is about twenty times what fills Sydney Harbour on a tide, because the bay is far bigger, at about 1,900 square kilometres. It is full by about seven in the morning, then drains back out all day.
How we made this reel
- We mapped the seabed. The depth of the harbour floor comes from a public survey.
- Then we ran the real tide. Sea levels measured at Fort Denison drove our own model of the harbour. Port Phillip Bay runs on the predicted tide at Point Lonsdale for 26 November 2026.
- Every line is moving water. Blue is coming in, gold is going out, brighter is faster. Tide alone moves the water, with no wind or rain.
What it means for you
- The sea does not reach every street the same way. Some blocks near the water carry far more coastal risk than the blocks beside them.
- Check it block by block. We score coastal risk for each small pocket of a suburb, so you can see your own street.
Where to see it on Microburbs
- Coastal risk, block by block. Every small pocket of a suburb gets its own coastal risk score.
- Your own home. The Risks section of every property report shows its coastal erosion check.
Get the data
Coastal risk for every block of a suburb is live in our API. In Bondi, Sydney, the coastal risk score ran from 0.03 to 0.23 from block to block. In St Kilda, on Port Phillip Bay, it ran from 0.01 to 0.81.
Try it now, free. This request is free for our sample suburbs, one in each state and territory, with no sign up and no card:
curl "https://api.microburbs.com.au/v1/suburbs/Bondi/mesh-blocks/hazard" \
-H "Authorization: Bearer test"
What it sent back on 12 November 2026, cut to one block and three fields:
{
"data": {
"suburb": "Bondi",
"state": "NSW",
"topic": "hazard",
"question": "Is it exposed to flood, fire or erosion?",
"block_count": 146,
"mesh_blocks": [
{
"mb_code": "10825880000",
"population": 72,
"dwellings": 36,
"fields": {
"in_erosion_prone_area": {
"value": 0.0,
"label": "Inside an erosion-prone area",
"unit": "1 = yes, 0 = no",
"provenance": "measured",
"measured_at": "mesh_block",
"how": "measured at this level"
},
"flood_risk_score": {
"value": 0.07,
"label": "Flood risk score",
"unit": "index 0-1",
"provenance": "not_recorded"
},
"coastal_risk_score": {
"value": 0.06,
"label": "Coastal risk score",
"unit": "index 0-1",
"provenance": "not_recorded"
}
}
}
]
}
}
See the full API docs for every request, the price of each and how to get a key for the rest of Australia.
See coastal risk block by block in any suburb
The sea doesn't reach every street the same way. Every small pocket of a suburb gets its own coastal risk score.



